HC-SFS201有大量库存

材质	1
产地	日本
产品种类	1
工作电压	220v
外形尺寸	12
品牌	三菱
适合机床	车床

  DEION Xenus combines CANopen networking with digital control of brushless or brush motors in an off-line powered package that can operate from single or three-phase mains with continuous power output to 4 kW. Xenus is offered in two versions based on the type of feedback. Standard models supports digital quadrature or analog sin/cos encoders. Resolver feedback is ailable in “-R” models which convert the resolver angle into quadrature encoder signals for using Xenus with ternal controllers. Xenus operates as a Motion Control Device under the DSP-402 protocol of the CANopen DS-301 V4.01 (EN 50325-4) application layer. DSP-402 modes supported include: Profile Position, Profile Velocity, Profile Torque, Interpolated Position (PVT), and Homing. Drive commissioning is fast and simple using CME 2 software operating under Windows? communicating with Xenus via CAN or an RS-232 link. CAN address selection is by a 16-position rotary switch on the front panel. If there are more than fifteen devices on a CAN bus, the additional address bits needed can come from programmable inputs, or can be set in flash memory. Profile Position Mode does a complete motion ind on command with S-curve acceleration & deceleration, top speed, and distance programmable. In PVT mode, the controller sends out a sequence of points each of which is an increment of a larger, more compl move than a single ind or profile. The drive then uses cubic polynomial interpolation to “connect the dots” such that the motor reaches each point (Position) at the specified velocity (Velocity) at the prescribed time (Time). Homing mode is configurable to work with a variety of limit, ind, and home switches such that the drive moves the motor into a position that has an absolute reference to some part of the machine. Eleven logic inputs are programmable as limit or home switches, stepper/encoder pulse inputs, reset, digital torque or velocity reference, or motor-temperature. A twelfth input is dedicated to the drive Enable. Three programmable logic outputs are for reporting a drive fault or other status indications. A fourth optically-isolated output can drive a motor brake from the ternal +24 Vdc power supply or can be programmed as a logic output. In addition to CANopen motion commands, Xenus can operate as a stand-alone drive. Current and velocity modes accept ±10 Vdc analog, digital 50% PWM or PWM/polarity inputs. In position mode inputs can be incremental position commands from step-motor controllers in Pulse/Direction or CW/CCW format, ±10 Vdc analog, or A/B quadrature commands from a master-encoder. Pulse to position ratio is programmable for electronic gearing. Power output of the drive varies with the input power which can range from to 240 Vac, and from 47 to 63 Hz. Either single or three phase mains can be used giving Xenus the ability to work in the widest possible range of industrial settings. Signal and control circuits are isolated from the high-voltage power supply and inverter stage that connect to the mains. A +24 Vdc input powers control circuits for keep-alive operation permitting the drive power stage to be completely powered down without losing position information or communications with the control system. ADP-055-18
ADP-090-09
ADP-090-18
ADP-090-36
ADP-180-09  HC-SFS201有大量库存
ADP-180-18
ACJ-055-09
ACJ-055-18
ACJ-090-03 

ACJ-090-09
ACJ-090-12
ACM-055-18  HC-SFS201有大量库存
ACM-090-09
ACM-090-24
ACM-180-09
ACM-180-18  
 
ACM-180-20
ACK-055-06
ACK-055-10
ACK-090-04
ACK-090-08
AEP-055-18
AEP-090-09 

AEP-090-18
AEP-090-36
AEP-180-09
AEP-180-18
APM-090-06
APM-090-14
APM-090-24
AEM-090-06
AEM-090-14
AEM-090-24
AP2-090-06
AP2-090-14